.\" LICENSE
.\"
.\" This software program is released under the terms of a license agreement between you ('Licensee') and Intel. Do not use or load this software or any associated materials (collectively, the 'Software') until you have carefully read the full terms and conditions of the LICENSE located in this software package. By loading or using the Software, you agree to the terms of this Agreement. If you do not agree with the terms of this Agreement, do not install or use the Software.
.\"
.\" * Other names and brands may be claimed as the property of others.
.\"
.
.TH ixgbe 1 "February 23, 2017"
.SH NAME
ixgbe \-This file describes the Linux* Base Driver
for the 10 Gigabit Family of Adapters.
.SH SYNOPSIS
.PD 0.4v
modprobe ixgbe [<option>=<VAL1>,<VAL2>,...]
.PD 1v
.SH DESCRIPTION
This driver is intended for \fB2.6.x\fR or later kernels. A version of the driver may already be included by your distribution and/or the kernel.org kernel.

This driver includes support for any 64 bit Linux supported system, including Itanium(R)2, x86_64, PPC64, ARM, etc.
.LP
This driver is only supported as a loadable module at this time. Intel is not supplying patches against the kernel source to allow for static linking of the drivers.


For questions related to hardware requirements, refer to the documentation
supplied with your Intel adapter. All hardware requirements listed apply to
use with Linux.
.SH OPTIONS
The following optional parameters are used by entering them on the
command line with the modprobe command.
For example:
.IP
modprobe ixgbe InterruptThrottleRate=16000,16000
.LP
.B RSS
.IP
.B Valid Range: 0-16
.IP
0 = Assign up to the lesser value of the number of CPUs or the number of queues
.IP
X = Assign X queues, where X is less than or equal to the maximum number of
queues (16 queues).
.IP
.IP
RSS also effects the number of transmit queues allocated on 2.6.23 and
newer kernels with CONFIG_NETDEVICES_MULTIQUEUE set in the kernel .config file.
CONFIG_NETDEVICES_MULTIQUEUE only exists from 2.6.23 to 2.6.26. Other options
enable multiqueue in 2.6.27 and newer kernels.
.LP
.B MQ - Multiqueue
.IP
.LP
.B Valid Range:
0, 1
.IP
0 = Disables Multiple Queue support
1 = Enabled Multiple Queue support (a prerequisite for RSS)
.LP
.B Direct Cache Access (DCA)
.IP
.B Valid Range: 0, 1
.IP
0 = Disables DCA support in the driver
.IP
1 = Enables DCA support in the driver
.IP
If the driver is enabled for DCA, this parameter allows load-time control of the feature.
.IP
Note: DCA is not supported on X550-based adapters.
.LP
.B IntMode
.IP
.B Valid Range: 0-2 (0 = Legacy Int, 1 = MSI and 2 = MSI-X)
.IP
IntMode controls allow load time control over the type of interrupt
registered for by the driver. MSI-X is required for multiple queue
support, and some kernels and combinations of kernel .config options
will force a lower level of interrupt support.
'cat /proc/interrupts' will show different values for each type of interrupt.
.LP
.B InterruptThrottleRate
.IP
.B Valid Range:
0=off
1=dynamic
<min_ITR>-<max_ITR>
.IP
Interrupt Throttle Rate controls the number of interrupts each interrupt
vector can generate per second. Increasing ITR lowers latency at the cost of
increased CPU utilization, though it may help throughput in some circumstances.
.IP
0 = Setting InterruptThrottleRate to 0 turns off any interrupt moderation
  and may improve small packet latency. However, this is generally not
  suitable for bulk throughput traffic due to the increased CPU utilization
  of the higher interrupt rate.
  NOTES:
  - On 82599, and X540, and X550-based adapters, disabling InterruptThrottleRate
    will also result in the driver disabling HW RSC.
  - On 82598-based adapters, disabling InterruptThrottleRate will also
    result in disabling LRO (Large Receive Offloads).
.IP
1 = Setting InterruptThrottleRate to Dynamic mode attempts to moderate
  interrupts per vector while maintaining very low latency. This can
  sometimes cause extra CPU utilization. If planning on deploying ixgbe
  in a latency sensitive environment, this parameter should be considered.
.IP
<min_ITR>-<max_ITR> = 956-488281
  Setting InterruptThrottleRate to a value greater or equal to <min_ITR>
  will program the adapter to send at most that many interrupts
  per second, even if more packets have come in. This reduces interrupt load
  on the system and can lower CPU utilization under heavy load, but will
  increase latency as packets are not processed as quickly.

.LP
.B LLIPort
.IP
.B Valid Range: 0-65535
.IP
LLI is configured with the LLIPort command-line parameter, which specifies
which TCP port should generate Low Latency Interrupts.
.IP
For example, using LLIPort=80 would cause the board to generate an immediate
interrupt upon receipt of any packet sent to TCP port 80 on the local machine.
.IP
WARNING: Enabling LLI can result in an excessive number of interrupts/second
that may cause problems with the system and in some cases may cause a kernel
panic.

Note: LLI is not supported on X550-based adapters.
.LP
.B LLIPush
.IP
.B Valid Range: 0-1
.IP
LLIPush can be set to be enabled or disabled (default). It is most effective
in an environment with many small transactions.
.IP
NOTE: Enabling LLIPush may allow a denial of service attack.

Note: LLI is not supported on X550-based adapters.
.LP
.B LLISize
.IP
.B Valid Range: 0-1500
.IP
LLISize causes an immediate interrupt if the board receives a packet smaller
than the specified size.

Note: LLI is not supported on X550-based adapters.
.B LLIEType
.IP
.B Valid Range: 0-0x8FFF
.IP
This parameter specifies the Low Latency Interrupt (LLI) Ethernet protocol type.

Note: LLI is not supported on X550-based adapters.
LLIVLANP
--------

Valid Range: 0-7

This parameter specifies the LLI on VLAN priority threshold.

Note: LLI is not supported on X550-based adapters.
.B FdirPballoc
.IP
.B Valid Range: 1-3
.IP
Specifies the Flow Director allocated packet buffer size.
1 = 64k
2 = 128k
3 = 256k
.BAtrSampleRate
.IP
Valid Range: 0-255
.IP
This parameter is used with the Flow Director and is the software ATR transmit
packet sample rate. For example, when AtrSampleRate is set to 20, every 20th
packet looks to see if the packet will create a new flow. A value of 0
indicates that ATR should be disabled and no samples will be taken.
.LP
.B L2LBen
.B Valid Range: 0 (disabled), 1 (enabled)
.IP
This parameter controls the internal switch (L2 loopback between pf and vf).
By default the switch is enabled.
.LP
.B LRO
.IP
.B Valid Range: 0(off), 1(on)
Large Receive Offload (LRO) is a technique for increasing inbound throughput
of high-bandwidth network connections by reducing CPU overhead. It works by
aggregating multiple incoming packets from a single stream into a larger
buffer before they are passed higher up the networking stack, thus reducing
the number of packets that have to be processed. LRO combines multiple
Ethernet frames into a single receive in the stack, thereby potentially
decreasing CPU utilization for receives.
This technique is also referred to as Hardware Receive Side Coalescing
(HW RSC). 82599 and X540, and X550-based adapters support HW RSC. The
LRO parameter controls HW RSC enablement.
.IP
You can verify that the driver is using LRO by looking at these counters in
ethtool:
.LP
- hw_rsc_aggregated - counts total packets that were combined
.LP
- hw_rsc_flushed - counts the number of packets flushed out of LRO
.IP
NOTE: IPv6 and UDP are not supported by LRO.
.LP
.B MDD (Malicious Driver Detection)
.IP
.B Valid Range: 0-1
.IP
0 = Disabled
.IP
1 = Enabled
.IP
This parameter is only relevant for devices operating in SR-IOV mode.
When this parameter is set, the driver detects malicious VF driver and
disables its Tx/Rx queues until a VF driver reset occurs.
.SH Jumbo Frames
.LP
Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) to a value larger than the default value of 1500.

Use the ifconfig command to increase the MTU size. For example, enter the following where <x> is the interface number:

   ifconfig eth<x> mtu 9000 up
Alternatively, you can use the ip command as follows:
   ip link set mtu 9000 dev eth<x>
   ip link set up dev eth<x>

.LP
NOTE: The maximum MTU setting for Jumbo Frames is 9710. This value coincides with the maximum Jumbo Frames size of 9728 bytes.

NOTE: This driver will attempt to use multiple page sized buffers to receive each jumbo packet. This should help to avoid buffer starvation issues when allocating receive packets.

NOTE: For 82599-based network connections, if you are enabling jumbo frames in a virtual function (VF), jumbo frames must first be enabled in the physical function (PF). The VF MTU setting cannot be larger than the PF MTU.
See the section "Jumbo Frames" in the Readme.
.SH SUPPORT
.LP
For additional information regarding building and installation, see the
README
included with the driver.
For general information, go to the Intel support website at:
.B http://www.intel.com/support/
.LP
If an issue is identified with the released source code on a supported kernel with a supported adapter, email the specific information related to the issue to e1000-devel@lists.sf.net.
.LP
